gC7 dimensions are shown: inch (mm) specifications and dimensions subject to change www .ck-components.com t series subminiature toggle switches f eatures/benefits ? c ompact sizemall footprint ? s ingle and double pole models ? p c and panel mount options available ? rohs compliant models available t ypical applications ? h and-held telecommunications ? i nstrumentation ? m edical equipment specifications cont act rating: b contact material: 0.4 va max. @ 20 v ac or dc max. q contact material (tx01 models): 3 amps @ 120 v ac or 28 v dc. all other models: 2 amps @ 120 v ac or 28 v dc. see page g-42 for additional ratings. electrical life: tx01 models: 60,000 make-and-break cycles at full load. all other models: 30,000 cycles. contact resistance: below 20 m typ. initial @ 2-4 v dc, 100 ma, for both silver and gold plated contacts. insula tion resistance: 10 9 min. dielectric strength: 1000 vrms min. @ sea level. opera ting tempera ture: C0?oto 85?. solderability : per mil-std-202f method 208d, or eia rs-186e method 9 (1 hour steam aging). note: any models supplied with p , r, q, b or g contact material ar e rohs compliant and compatible. note: specifications and materials listed above are for switches with standard options. for information on specific and custom switches, consult customer service center. materials case: glass filled nylon 6/6, flame r etardant, heat stabilized or diallyl phthalate (dap), (ul 94v-0). actuator: brass, chrome plated. bushing: brass, nickel plated. h ousing: stainless steel. switch support: brass, matte-tin plated. end cont acts: b contact material: copper alloy, with gold plate over nickel plate. q contact material: coin silver, silver plated. see above for additional contact materials. center contacts & terminals: b contact material: copper alloy, with gold plate over nickel plate. q contact material: copper alloy, silver plated. see page g-42 for additional contact materials. terminal seal: epoxy. hardw are: nut & locking ring: brass, nickel plated. lockwasher: steel, nickel plated. additional hardware available separately , see section o. build-a-switch to order, simply select desired option from each category and place in the appropriate box. available options are shown and described on pages g-38 thru g-42. for additional options not shown in catalog, consult customer service center . all models have epoxy terminal seal and are compatible with all ottom--ash?cb cleaning methods. switch function t101 spdt on-none-on t102 spdt off-none-on t103 spdt on-off-on t105 spdt mom.-off-mom. t107 spdt on-off-mom. t108 spdt on-none-mom. t201 dpdt on-none-on t205 dpdt mom.-off-mom. t203 dpdt on-off-on t207 dpdt on-off-mom. t208 dpdt on-none-mom. t211 dpdt on-on-on. actuator p3 flatted, anti-rotation, .490" high s .370" high k locking lever, round tip l1 .620" high m1 .220" high s1 .410" high m .210" high l .290" high t erminations a right angle, pc thru-hole a v v ertical right angle, pc thru-hole c pc thru-hole v3 vertical mount v-bracket z solder lug w wire wra p bushing h .220" high, threaded, flat h9 .220" high, unthreaded, flat cf splashproof, .310" high, threaded, flat d9 .260" high, unthreaded, keyway t .310" high, threaded, flat t9 .310" high, unthreaded, flat td .260" high, threaded, keyway tk .310" high, threaded, keyway y .220" high, threaded, keyway y9 .220" high, unthreaded, keyway contact material b gold p gold, matte tin q silver g gold over silver r gold over silver, matte-tin seal e epoxy m odels available g t o g g l e
gC8 dimensions are shown: inch (mm) specifications and dimensions subject to change www.ck-components.com t series subminiature toggle switches switch function dpdt mom. = momentary all models with all options when ordered with g, l, r or q contact material. s pdt s pst 2 -1 2-1 3-1 n /a open n/a 2 -3 2-3 open o nn one on on off on m om. off m om. on off m om. off n one on t101 t103 t105 t107 t102 sp s chemat ic connected t erm inals pos. 1 po s. 2 po s. 3 switch functio n pos. 1 pos. 2 pos. 3 model no. no. poles c&k m ark ing on o p po site side c&k marking on opposi te side t108 2-1 n a 2 -3 m om. none on spdt part number shown: t101shzqe d pdt 2-1,5 -4 2-1,5 -4 n/a open 2-3, 5-6 2-3, 5-6 on n one on m om. off m om. t201 t205 dp t203 on off on t208 t211* on n one m om. 2 -1,5 -4 n/a 2-3, 5-6 2-1,5 -4 2-3, 5-6 2 -3, 5-4 on on o n. s chemat ic connected t erm inals pos. 1 po s. 2 po s. 3 switch functio n pos. 1 pos. 2 pos. 3 model no. no. poles c&k mark ing on o p po site side c &k marking on opposite s ide terminal nos. for reference only part number shown: t201shzqe g t o g g l e
g t o g g l e gC9 dimensions are shown: inch (mm) specifications and dimensions subject to change www .ck-components.com t series subminiature toggle switches actuator bushing 2 locking positions C1 & ?C models 2 position lock C3 & ?1 models 3 position lock C8 models 1 position lock 2 2 1 h .220" high threaded, flat y .220" high threaded, keyway t .310" high threaded, flat h9 .220" high unthreaded, flat y9 .220" high unthreaded, keyway t9 .310" high unthreaded, flat l1 .620" high l .290" high k locking lever p3 a nti-rotation, flatted, .450" high s .370" high m .210" high m1 .220" high (with ?ushing) s 1 .410" high (with ?ushing) a vailable with t & t9 bushings only . dress nut part number 709901201 supplied standar d with thr eaded bushing. 1 actuator shown with standard h bushing. subtract .040 (1,02) for td and d9 bushings, subtract .090 (2,29) for t, t9, tk, k9 & cf bushings. 2 a ctuators shown with t, t9, tk & cf bushings, add .050 (1,27) for td and d9 bushings, add .090 (2,29) for h, h9, y & y9 bushings. a ll actuators have chrome finish (except k). not available with cf bushing option. bushing option code not required. not available with tx05 & tx07 models. k actuators have natural aluminum finish. keyway on right side. to prevent accidental actuation, toggles must be lifted before being actuated. when released, toggles again lock in place. overtightening mounting nut may cause actuator to bind. h standard with c, w & z terminations. h9 standar d with a, a v & v3 terminations. standard with z, c or w terminations. s tandard with a, av or v3 terminations. 1 1
gC0 dimensions are shown: inch (mm) specifications and dimensions subject to change www.ck-components.com t series subminiature toggle switches bushing terminations pane l mounting 10-48 bushing without locking ring with standard locking ring 1/4 in. bushing with standard locking ring without locking ring with small locking ring without locking ring without locking ring sp dp pc mounting t102 Comit center hole. sp dp sp dp tk .310" high threaded, keyway z solder lug w wire wrap c pc thru-hole td .260" high threaded, keyway d9 .260" high unthreaded, keyway cf splashproof, .310" high threaded, flat i p67 degree of protection. internal o-ring actuator seal and external bushing seal washer standard. not available with k locking lever option. not available with p or r contact materials. g t o g g l e
g t o g g l e gC1 dimensions are shown: inch (mm) specifications and dimensions subject to change www .ck-components.com t series subminiature toggle switches terminations a ctuator shown in pos. 1 pc mounting actuator shown in pos. 1 pc mounting actuator shown in pos. 1 pc mounting actuator shown in pos. 1 pc mounting t102 models: omit terminal 2 actuator shown in pos. 1 pc mounting t102 models: omit center hole. a right angle, pc thru-hole a right angle, pc thru-hole a v ver t ical right angle, pc thru-hole a v ver tical right angle, pc thru-hole v3 vertical mount, v-bracket not available with t102 model. note: terminal bend radii and lead-in manufacturing option. t102 models: omit terminal 2 note: terminal bend radii and lead-in manufacturing option. t101mh9abe horizontal actuation spdt t201mh9abe horizontal actuation dpdt t101mh9avbe vertical actuation spdt t201mh9avbe vertical actuation dpdt t101mh9v3be spdt
gC2 dimensions are shown: inch (mm) specifications and dimensions subject to change www.ck-components.com t series subminiature toggle switches terminations actuator shown in pos. 1 pc mounting v3 vertical mount, v-bracket cont act material * note: see t echnical data section of this catalog for rohs compliant and compatible definitions and specifications. 1 contacts & terminals: copper alloy, with gold plate over nickel plate. 2 end cont acts: coin silver, with gold plate over nickel plate. 3 center contacts & all terminals: copper alloy, with gold plate over nickel plate. 4 end contacts: coin silver, silver plated. 5 center contact & all terminals: copper alloy, silver plated. 6 terminals: copper alloy , with matte-tin over nickel plate. note: any models supplied with p , r, q, b or g contact material ar e rohs compliant. for the latest information r egarding rohs compliance, please go to: www.ittcannon.com/rohs. all models with all options when ordered with r, g, l or q contact material. b contact material standard with a, av, v3 & w terminations. q contact material standard with c & z terminations. k, l and m options represent non rohs tin lead product and are not recommended for new designs. for additional information please contact customer service. seal e epoxy seal t201mh9v3be dpdt option code contact material terminal plating ratings silver 5 gold 1 silver 4 ,5 gold over sil ver 2,3 gold 3 matte-tin 6 gold 1 ma tte-tin 6 low level/ d ry circuit power low level/dr y circuit or power 0 .4 va max. @ 20 v ac or dc max. tx01 models: 3 amps @ 120 v ac or 28 v dc. all other models: 2 amps @ 120 v ac or 28 v dc. tx01 models: 0.4 va max @ 20 v ac or dc max. or 3 amps @ 120 v ac or 28 v dc. all other models: 0.4 v a max @ 20 v ac or dc max. or 2 amps @ 120 v ac or 28 v dc. b p q g r g t o g g l e
|
